Ford 1700 tractor manual pdf free download

Elsevier Books Reference. Related Audiobooks Free with a 30 day trial from Scribd. Elizabeth Howell. Views Total views. Actions Shares. No notes for slide. Ford tractor service repair manual 1.

Customary systems of measurement. The first specification is given in the measuring system used during manufacture, whiie the second specification given in parenthesis is the converted measurement. For instance, a specification of "0. Stroke 80 mm 3. Displacement cc Exhaust 0. Fuel Tank 14 L 3. Flywheel N-m ft. Cylinder Head N-m ft.

Front Axle Differential Case 1. Cylinder Head N-m 48 N-m ft-lbs. Main Bearing Holders Note 1: 61 N-m 45 ft. Note 2: N-m ft. The front axle may be fixed tread width type or adjustable type for , , , , , , and models as shown in Figs. The adjustable axle used on , , and models is shown in Fig.

Adjustable axle used on Off- set tractor is shown in Fig. Front wheel toe-in is set by adjusting the length of the tie rod. Clearance between axle pivot shaft and bushings Figs. Bushings should be renewed if clearance exceeds 0.

Front wheel hub outer half 2. Nut 3. Outer bearinjj 4. Collar 6. Inner bearing 7. Seal 8. Seal 9. Wheel hub inner half Spacer U. Spindle Oil seal Bearing washers Needle thrust bearing Bushings Axle Washer Steering arm Cotter pin Castelated nut Shim Bushing Pivot shaft 7.

When renewing spindle bushings 15 , the top bushing should be pressed into bore until bushing is 4. On models equipped with a lip type seal Figs. Install seal with lip facing upward. Front wheel bearings should be re- moved, cleaned, inspected, renewed if damaged and packed with a good quality No.

Tighten wheel bearing retaining nut 2 until slight drag is noticed while rotating wheel hub, then loosen nut to first castellation and install cotter pin. The front axle of four wheel drive models includes the differential as- sembly, axle housings, drive shafts, universal joints and final drives. Refer to appropriate paragraphs 3 through 12 for service to components. Models So Equipped 3. To remove the complete front drive axle as- sembly, first raise front of tractor and Fig.

Cover 2. Outer b »aring i. Inner iH'aring 7. Spacer 9. Hub Seal Bearing washer Fixed tread axle Shims Washers Axle center member Axle extension Pivot casting Gasket Snap ring 30 37 18 Ftg. Refer to Fig. Spacer 'M. Retainer Fig. Axle extensions place a support behind the axle. Detach drag link from steering arm. Place front wheel drive control lever in "disengaged" position.

Loosen clamps that attach drive shaft cover at the rear. Support axle to prevent tipping, then remove cap screws attaching axle pivot brackets to front support. Carefully lower axle until it can be moved forward out of drive shaft splines.

Inspect axle pivot bushings 13 and Figs. Spacer Retainer inch for and models; 82 mm I-V4 inches for and models; between differential case trunnions and Fig. Nut Needle thrust l earirig Axle tenter? Outer tearing Axle extension 6. Injier hearing Pivot casting 7. Shim 3fi. Bearing washer 2H. Thrust washer bushings exceeds 0.

When reinstalling axle, observe the following: Move axle assembly carefully into position while sliding drive shaft splines and pinion shaft splines into coupling. Tighten screws attaching pivot brackets to front support, then check ax- le housing fore and aft end play. Desired end play is 0. If end play exceeds 0. Stop bolts 49 - Figs. Stop bolt setting is measured from head of bolt to surface of mounting pad.

To remove the outer drive, first remove wheel and tire. Detach drag link and tie rod from axle steering arm. Remove plates and seal parts 65 through Figs. Support the outer drive unit, then unbolt and remove king pins 47 and Withdraw assembly from axle housing On early and models, uni- versal joint Fig.

To remove universal joint first separate outer cover 63 from housing 57 and remove snap ring 55 from end of shaft. Tap universal joint and shaft out of bear- ings 52 and 54 and pinion gear. Remove wheel axle 64 , gear 59 , bear- ings and seals from outer cover and housing. On late and models and all , , and models, pin- ion shaft is integral with the pinion gear Figs.

To disas- semble outer drive, remove snap ring from inner end of pinion shaft Un- bolt and separate outer cover 63 from housing Remove nut and washer 71 , then tap wheel axle 64 out of bear- ings and gear. Remove pinion gear, bearings and seals from housing and cover. On all models, backlash between pin- ion gear 53 and final drive gear 59 should be 0. If backlash exceeds 0. Clearance between king pins 47 and 50 and bushings 45 should be 0, Max- imum allowable clearance is 0.

To reassemble, reverse the dis- assembly procedure. Note that shims Fig. Paragraph 5 FORD 1. Drive shall housing 5. Snap rings 6.

Universal joint 7. Drive shaft 8. Coupling Pin 6x32 mm Rear carrier bracket Pinion bearing Snap rings Snap ring Besides, accessories, units and parts Ford has long been in demand in all parts of the world.

Ford Tractor Logo. Ford Tractors. Ford Tractor. We Use Cookie We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. Manage consent. Close Privacy Overview This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website.

When replacement of parts during repair work is needed, be sure to use genuine parts. Ford tractor manual. A historically accurate parts manual is essential when ordering parts. Manual We hope it can be fixed perfectly. Ford tractor repair manual You can access, read and save it in your desktop. This is a Service Manual for the Ford with pages of important information pertaining to your Ford tractor. This is a reprint of the original factory repair manual and contains the information you need to take your Ford tractor apart, fix it.

PDF format for download. Description; Ford — 60 pages — Manual Code: